久草福利视频-久久精品综合-久久不射网-天天插夜夜操-婷婷99-国产伦精品一区二区三区四区免费-www.日本高清-亚洲国产专区-日韩免费专区-夜夜操夜夜干-中文字幕第23页-久久爱99-欧美区国产区-中文有码在线播放-2017狠狠干-天天射,天天干-国产av不卡一区二区-99久久久无码国产精品不卡-日韩亚洲欧美中文字幕-99热都是精品

靜態壓力在所有方向上均勻施加，而速度壓力僅在氣流方向上施加。這使得直接測量管道中的速度壓力變得困難。
The static pressure is applied uniformly in all directions, while the velocity pressure is applied only in the air flow direction. This makes it difficult to directly measure the velocity and pressure in the pipeline.
簡單地說，因為靜壓力也在向氣流的方向推動，所以無法測量靜速度壓力。實際上，速度壓力是通過測量垂直于氣流的壓力（靜壓）和平行于氣流的壓力（總壓）來計算的。
Simply put, because the static pressure is also pushing in the direction of the air flow, the static velocity pressure cannot be measured. In fact, the velocity pressure is calculated by measuring the pressure perpendicular to the air flow (static pressure) and the pressure parallel to the air flow (total pressure).
靜態壓力和速度壓力是相互轉換的。每個管道的大小取決于決定流量的局部管道橫截面速度。
Static pressure and velocity pressure are converted to each other. The size of each pipe depends on the local pipe cross-section velocity that determines the flow rate.


管道中的壓力變化受以下影響：恒定橫截面積：總損失和靜態損失相等。分流段（管道尺寸增加）：速度壓力增加，總壓力降低，靜態壓力可能增加（靜態回潮率），收斂段（管道尺寸減小）：流速壓力沿流向增加，總壓和靜壓降低。
The pressure change in the pipeline is affected by the following: constant cross-sectional area: the total loss is equal to the static loss. In the diverging section (the pipeline size increases): the velocity pressure increases, the total pressure decreases, the static pressure may increase (static moisture regain), and the convergence section (the pipeline size decreases): the velocity pressure increases along the flow direction, and the total pressure and static pressure decrease.
由于摩擦和湍流損失，總壓通常沿氣流下降。常州螺旋風管的承包商混合使用“靜壓”、“速度壓力”和“總壓”等術語非常普遍。術語“靜態壓力”通常用于風機選擇；“速度壓力”用于測量系統中的cfm，“總壓力”用于查找速度壓力。總壓力決定了必須提供給系統。
Due to friction and turbulence losses, the total pressure usually drops along the flow. It is very common for Changzhou spiral duct contractors to use the terms of "static pressure", "velocity pressure" and "total pressure". The term "static pressure" is usually used for fan selection; "speed pressure" is used to measure CFM in the system, and "total pressure" is used to find the speed pressure. The total pressure determines that it must be provided to the system. 上一篇：通風管道中風管與支吊架的安裝闡明
下一篇：山東通風管道工程安裝的關鍵點有哪些？