久草福利视频-久久精品综合-久久不射网-天天插夜夜操-婷婷99-国产伦精品一区二区三区四区免费-www.日本高清-亚洲国产专区-日韩免费专区-夜夜操夜夜干-中文字幕第23页-久久爱99-欧美区国产区-中文有码在线播放-2017狠狠干-天天射,天天干-国产av不卡一区二区-99久久久无码国产精品不卡-日韩亚洲欧美中文字幕-99热都是精品

如今很多場所下都需要進行風管安裝，以保證場所下的通風工作，保證環境下的整潔和設備安全使用，當然在安裝時也要采用正確的方法，那么通風管道安裝方法是什么？跟隨高氏一起看下吧。

improve air circulation Follow Gao to have a look.

(1)風管組裝:當風管較短時，可一次在地面組裝而成，當風管較長時，可視安裝場地的情況，在地面分段組裝。組裝時應盡量調整風道的度和水平度，避免風管扭曲或上下起波，左右擺龍，每段風道不宜超過10m。

(1) Air duct assembly: when the air duct is short, it can be assembled on the ground at one time. When the air duct is long, it can be assembled in sections on the ground according to the situation of the installation site. During assembly, the center and levelness of the air duct should be adjusted as far as possible to avoid the distortion of the air duct or wave up and down, and the left and right swing dragons. Each section of the air duct should not exceed 10m.

組裝時，墊片應墊平，法蘭螺栓應均勻擰緊，螺母帽均朝向同一方向。

During assembly, the gasket should be padded flat, the flange bolts should be tightened evenly, and the nut caps should face the same direction.

(2)風管就位:風管就位前應檢查全部支架的水乎度和標高、檢查支架的牢固程度，風管就位可采用直接和吊具兩種方法。對風管斷面較小，又位置較低的可采用人工就位方法，只需搭設簡易腳手架即可。

(2) Air duct in place: before the air duct is in place, check the water tightness and elevation of all supports, and check the firmness of supports. Direct and sling methods can be used for air duct in place. If the cross section of the air duct is small and the position is low, the manual positioning method can be adopted, and the simple scaffold can be set up.

當風管斷面較大且管段較長時，可采用滑輪、倒鏈、大繩等方法吊裝。世紀星介紹為了便于風道就位，一般多采用將風道吊在腳手架上，然后再將其抬放在風道支架上的方法。腳手架應沿其風道長度方向搭設，高度和位置應適合施工操作，吊裝順序應先干管后支、立管，吊起時，吊點應牢固，兩吊點應均勻受力。

When the cross-section of air duct is large and the pipe section is long, pulley, chain block, rope and other methods can be used for hoisting. Century Star introduces that in order to make the air duct in place, the air duct is usually hoisted on the scaffold, and then lifted on the air duct bracket. The scaffold shall be erected along the length of its air duct, and the height and position shall be suitable for construction operation. The hoisting sequence shall be the main pipe first and then the support and riser. When hoisting, the hoisting points shall be firm, and the two hoisting points shall be evenly stressed.

(3)風道調直:就位在支架上的風道，應撥正位置，調整風道橫平豎直，然后再按圖集要求固定。

(3) Air duct straightening: the air duct in place on the bracket should be straightened, adjusted horizontally and vertically, and then fixed according to the requirements of the atlas.

以上是雙恩空調有關通風管道安裝的具體介紹，在通風管道安裝時需要采用正確的方法，按照流程操作，保證順利完成安裝。

improve air circulation