久草福利视频-久久精品综合-久久不射网-天天插夜夜操-婷婷99-国产伦精品一区二区三区四区免费-www.日本高清-亚洲国产专区-日韩免费专区-夜夜操夜夜干-中文字幕第23页-久久爱99-欧美区国产区-中文有码在线播放-2017狠狠干-天天射,天天干-国产av不卡一区二区-99久久久无码国产精品不卡-日韩亚洲欧美中文字幕-99热都是精品

　　風管驗收的步驟通常包括以下幾個關鍵環節，以確保風管系統的安裝質量和性能符合設計要求及相關標準：

　　The steps of duct acceptance usually include the following key steps to ensure that the installation quality and performance of the duct system meet the design requirements and relevant standards:

　　一、檢查設備與材料

　　1、 Check equipment and materials

　　核對內外機型號：確保風管機的內外機型號與合同或設計圖紙上的一致。

　　Check the models of the internal and external units: Ensure that the models of the internal and external units of the air duct fan are consistent with those on the contract or design drawings.

　　檢查機器外觀：查看風管機及輔助設備（如銅管、保溫管、冷凝管等）是否有磕碰變形或損壞。

　　Check the appearance of the machine: Check whether the air duct fan and auxiliary equipment (such as copper pipes, insulation pipes, condenser pipes, etc.) are bumped, deformed or damaged.

　　核對輔料品牌型號：檢查所有使用的輔料（如螺絲、管卡、扎帶等）的品牌和型號是否符合要求。

　　Verify the brand and model of auxiliary materials: Check whether the brand and model of all auxiliary materials used (such as screws, pipe clamps, zip ties, etc.) meet the requirements.

　　二、檢查安裝工藝

　　2、 Check the installation process

　　內機安裝：

　　Installation of internal unit:

　　檢查吊桿是否使用雙螺母減震，以減少運行噪音。

　　Check if the suspension rod uses double nuts for shock absorption to reduce operating noise.

　　確保內機至少下吊2厘米，避免出風口受遮擋。

　　Ensure that the internal unit is lowered at least 2 centimeters to avoid blocking the air outlet.

　　檢查內機安裝后是否用保鮮膜纏繞并包裹防塵罩，以及是否標注了出風口和回風口的尺寸。

　　Check whether the internal unit is wrapped with cling film and wrapped with a dust cover after installation, and whether the dimensions of the air outlet and return outlet are marked.

　　管卡與密封：

　　Pipe clamps and seals:

　　檢查管卡間距是否符合要求（通常為1.2米）。

　　Check if the spacing between pipe clamps meets the requirements (usually 1.2 meters).

　　確保螺絲管卡使用不銹鋼材質，以提高耐腐蝕性。

　　Ensure that the screw pipe clamp is made of stainless steel material to improve corrosion resistance.

　　檢查接頭處是否用扎帶密封，墻縫接觸處是否打發泡膠防止移位。

　　Check if the joints are sealed with zip ties, and if foam glue is applied to the wall joints to prevent displacement.

　　銅管與排水管：

　　Copper pipes and drainage pipes:

　　檢查銅管折彎是否使用折彎機，避免折扁影響流量。

　　Check if a bending machine is used for bending copper pipes to avoid flattening and affecting flow.

　　確保排水管有坡度，方便冷凝水排出。

　　Ensure that the drainage pipe has a slope to facilitate the discharge of condensed water.

　　檢查排氣管是否做彎頭，防止灰塵進入。

　　Check if the exhaust pipe is bent to prevent dust from entering.

　　電源線：檢查空調電源線是否達到4平方以上，以防止過載發熱產生安全隱患。

　　Power cord: Check if the air conditioning power cord is over 4 square meters to prevent safety hazards caused by overload and heating.

　　三、性能測試與實驗

　　3、 Performance testing and experimentation

　　冷媒管路打壓測試：對冷媒管路進行打壓測試（如40公斤壓力），保壓48小時檢查氣密性。

　　Refrigerant pipeline pressure test: Conduct a pressure test on the refrigerant pipeline (such as 40 kg pressure), hold the pressure for 48 hours, and check the airtightness.

　　冷凝水管排水實驗：進行冷凝水管排水實驗，確保排水順暢無阻。

　　Condensation pipe drainage experiment: Conduct a condensation pipe drainage experiment to ensure smooth and unobstructed drainage.

　　運行測試：開啟風管機進行運行測試，檢查是否有異常噪音、振動或漏風現象。

　　Run test: Turn on the air duct fan for a run test to check for any abnormal noise, vibration, or air leakage.

　　四、記錄與報告

　　4、 Record and Report

　　記錄驗收結果：詳細記錄每一步的驗收結果，包括合格與不合格項。

　　Record the acceptance results: Detailed records of each step's acceptance results, including qualified and unqualified items.

　　編寫驗收報告：根據驗收結果編寫驗收報告，總結風管機的安裝質量和性能是否符合要求。

　　Write acceptance report: Based on the acceptance results, write an acceptance report summarizing whether the installation quality and performance of the air duct fan meet the requirements.

　　整改與復驗：對于不合格項，要求安裝單位進行整改，并重新進行驗收直至合格。

　　Rectification and re inspection: For non-conforming items, the installation unit is required to rectify them and conduct re acceptance until they are qualified.

　　綜上所述，風管驗收的步驟涵蓋了設備與材料的檢查、安裝工藝的檢查、性能測試與實驗以及記錄與報告等多個方面。這些步驟確保了風管系統的安裝質量和性能符合設計要求及相關標準，為后續的使用和維護提供了有力保障。

　　In summary, the steps of air duct acceptance include equipment and material inspection, installation process inspection, performance testing and experimentation, as well as recording and reporting. These steps ensure that the installation quality and performance of the duct system meet the design requirements and relevant standards, providing strong support for subsequent use and maintenance.

　　本文由  山東通風管道 友情奉獻.更多有關的知識請點擊   http://www.qdqrsj88.com  真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from Shandong Ventilation Duct For more related knowledge, please click http://www.qdqrsj88.com Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.